Alto LYNX-MIX244 USB User Manual download pdf (Page 10)

SPOTLIGHT

4. CONTROL ELEMENTS

17 ASSIGNMENT Switches

Each channel provides four push-buttons: SUB1-2, SUB3-4, MAIN L-R and SOLO.

Pressing the SOLO button, the corresponding SOLO LED will illuminate and the

SOLO signal will replace other signals send to the Headphone/Control Room and

Meters. We suggest use the SOLO function in live work to preview channels

before they are let into the mix. It is useful to set an instrument's input level and

EQ, and you can also solo any channel that you want to. The SOLO switch never

affects any mix other than the Control Room. The other three buttons can be

considered as signal assignment switches. Pressing the SUB1-2 will assign the

channel signal to Su/jointfilesconvert/370231/bgroup1/2, you can depend on the PAN switch to adjust the

amount of channel signal sent to the SUB1 versus SUB2, when turned

completely left, then the signal can be only controlled by Su/jointfilesconvert/370231/bgroup1 and vice-

versa. In the same way, pressing the SUB3-4 or MAIN L/R will assign the channel

signal to Su/jointfilesconvert/370231/bgroup3/4 or MAIN MIX L/R, and will also be affected by PAN.

the PAN

18 FADER

This fader will adjust the overall level of this channel and set the amount of signal

send to the main output.

3. CONTROL ELEMENTS

SPOTLIGHT

4. CONTROL ELEMENTS

19 Master AUX SENDS Controls

20 SOLO Button

The function of these SOLO buttons are the same as the channel SOLO button,

they can also be affected by the SOLO MODE switch. Press the Solo button,

the AUX sends ( will be routed to the Ctrl Room/Phones outputs and

Meters display.

1~3)

These four controls are used to determine the master AUX SEND levels, which

can be varied from - to +15 dB. When the external effect units which

connected to mixer, you can get a further +15 dB

gain available from these Aux Send outputs. As to the AUX4, it can also provide

the lovable level adjustment for the internal effect signal.

has

no input gain control were

21 Master STEREO AUX RETURNS Controls

These two controls set the level that received from the stereo AUX RETURN

connectors, which can be varied from - to +15 dB. They are used to provide the

further gain for low level effects.

These 1/4" phone jacks will be used to send the Control Room signal to the

studio monitor speakers or a second set of PA.

48 CTRL OUT Jacks

These jacks will be used to send the signal to a pair of headphone or to powered

studio monitors.

49 PHONES Jacks

- TAPE IN

Use the Tape input if you wish to listen to your mix from a Tape Recorder or DAT.

- TAPE OUT

These RCA jacks will route the main mix into a tape recorder.

51 2-TRACK IN/OUT

This switch is used to turn the main power on and off.

52 POWER Switch

53 +48 Volt Phantom Power

It is available only to the XLR MIC sockets. Never plug in a microphone when

phantom power is already on. Before turning phantom power on, make sure

that all faders are totally down. In this way, you will protect your stage

monitors and main loudspeakers.

Use it to connect your LYNX-MIX244 mixer to the main AC with the supplied

AC cord. Please check the voltage available in your country and how the

voltage for your LYNX-MIX244mixer is configured before attempting to connect

your LYNX-MIX244 mixer to the main AC.

54 AC Inlet with FUSE Holder

Rear Panel

PHANTOMPOWER

OFF

AC INPUT

100-240V 50/60Hz

RATED POWER CONSUMPTION: 70W

Fuse: T-1.6AL

Apparaten skall anslutas

till jordat uttag nar den

ansluts till ett natverk

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

REPLACE WITH THE SAME TYPE FUSE AND RATING

DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE

WARNING: SHOCK HAZARD

AVIS: RISQUE DE CHOC ELECTRIQUE

- DO NOT OPEN

- NE PAS OUVRIR

SERIAL

MODEL

52 53

internal DSP module and the signal level can be controlled by the EFFECTS

OUT (37) control.

This 1/4" phone jack is balanced/unbalanced mono mix output connector, it can

be regarded as a sum output of the left and right of MAIN MIX.

50 MONO OUTPUT Jack

22 TO AUX SEND1/2

The both rotary knobs assign the AUX RETURN 2 signals to their respective

AUX SEND outputs: The "TO AUX SEND1" assign the signal to AUX SEND1

bus, and the "TO AUX SEND2" assign the signal to AUX SEND2 bus. The

adjustable range goes from - to +15 dB.

1 2 ... 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Alto LYNX-MIX244 USB User Manual Page 10

Comments to this Manuals

Related products and manuals for Audio mixers Alto LYNX-MIX244 USB